Skip to content

8 years in business. 2-yr workmanship warranty. Free estimate (843) 350-8732

James Island · Charleston · Mount Pleasant · Hanahan

(843) 350-8732

ServicesGutter Repair

Gutter Repair in James Island

We fix sagging, leaking and pulled-loose gutters on your home with parts that suit the metal you already have. Aluminum, steel, copper and vinyl each fail in their own way. We find the cause, show you photos and give you a written estimate before any work starts.

Worker on an aluminum ladder applying sealant with a caulk gun to a white gutter seam near the corner of a brick house, with a downspout at right

Fix what is failing, keep what still works

Most gutter problems are local. One seam opens up, a few hangers pull out of soft wood, or a low spot holds water and starts to rust. A good repair handles that section and leaves the rest of the run alone.

The material decides how we fix it. Aluminum gets resealed with a sealant made for metal gutters and riveted where it has pulled apart. Galvanized steel needs the rust cut back before any patch will hold. Copper is soldered, not caulked. Vinyl joints are swapped out, because brittle vinyl does not take a patch well.

We have been in business 8 years, and we will tell you plainly when a run is past saving. If replacing makes more sense, our Gutter Installation page walks through the options.

What a gutter repair covers

Resealing seams and end caps

We scrape out the old sealant, dry the joint and reseal it. Joints that have pulled apart get new rivets first so the seal is not doing all the work.

Rehanging sagging runs

Loose spikes get replaced with hidden hangers and screws driven into solid fascia. We space them closer where the run carries a lot of roof water.

Re-pitching runs that hold water

A gutter needs a slight fall toward its outlet. When a section has settled flat or backward, we reset the hangers so water moves instead of sitting.

Patching holes and rust spots

Small holes in aluminum or steel get a matching metal patch set in sealant. Copper gets a soldered patch. Large rusted areas usually mean that piece should be replaced.

Parts that match your metal

We do not mix copper with aluminum or steel. Different metals touching in wet, salty air corrode each other fast, so every fastener and patch matches what is already up there.

Signs your gutters need repair

  • Water pouring over the front edge

    If water sheets over the lip in a hard rain, the run may be pitched wrong or pulling away from the roof edge.

  • Drips at the joints

    Steady drips at corners and seams mean the sealant has failed. Left alone, that water stains siding and soaks the fascia.

  • Sagging or gaps at the roofline

    A gutter that dips or leans out has lost its hangers. Each storm puts more weight on the ones that are left.

  • Peeling paint or soft fascia

    Paint that blisters behind the gutter, or wood that gives when you press it, points to a slow leak that has been running for a while.

  • Rust streaks or white powder

    Orange streaks on steel and chalky white spots on aluminum are corrosion. Near the coast they can turn into holes faster than you would expect.

How a repair job runs

  1. 1

    Free inspection

    We walk the whole system, not just the spot you noticed. You get photos of what we find and what is causing it.

  2. 2

    Written estimate

    We list each repair line by line. If a section is not worth fixing, we say so and show you why.

  3. 3

    Repair day

    Most repairs take a few hours. We set ladders on pads, keep off your plants where we can, and work section by section.

  4. 4

    Water test and cleanup

    We run water through the repaired runs to check for drips and flow. Old hangers, scraps and sealant tubes leave with us. Our work is backed by a 2-year workmanship warranty.

What moves the price of a repair

Repair pricing depends on what we find once we are up on the ladder. We give you a written estimate after the inspection, so you see the cost before we start. These are the things that change it most.

Gutter material
Aluminum and vinyl repairs are usually simpler. Copper takes soldering and costs more in parts. Steel with heavy rust takes extra prep.
How much is damaged
One leaking corner is a small job. Rehanging and re-pitching a full side of the house takes more time and more hangers.
Height and access
A two-story run or a steep roof edge takes more setup and safety gear than a single-story eave.
Fascia condition
If the wood behind the gutter is rotten, hangers have nothing to hold. That board has to be dealt with before the gutter can go back up.

Gutter repair questions

Something not covered here? (843) 350-8732

Should I repair my gutters or replace them?

If the damage is limited to a few joints or one sagging section, repair is usually the right call. If rust or splits show up along most of the run, patches will keep failing. We show you photos and give you an honest answer either way.

Can you match my existing gutters?

In most cases, yes. We match the material and profile so patches and new pieces fit the old run. Very old or odd profiles can be harder to match, and we will tell you that up front.

Do you repair copper gutters?

Yes. Copper joints and holes are soldered, which holds far longer than caulk on copper. We use copper fasteners and hangers so nothing reacts with the metal.

Is the repair work covered?

Yes. Our repairs carry a 2-year workmanship warranty. If a joint we sealed or a section we rehung fails because of how we did the work, we come back and fix it.

Will insurance pay for storm damage to my gutters?

Sometimes, depending on your policy and the cause. We are not the adjuster, but we can document the damage with photos and a written estimate you can share with your insurance company.

Brick ranch home's covered back patio with a new black gutter and a downspout running down a white post to a splash block, with a stepladder and toolbox on the lawn

Find out what your gutters need

Give us a ring and describe the leak, sag or rust you have spotted, and we will set a time to look it over in person. You get photos, a written estimate and an honest call on whether to repair or replace.